What Size Solar Generator Do I Need?

The size you need comes down to two separate numbers, not one: how many watts (W) you need to power your devices at the same moment, and how many watt-hours (Wh) of stored energy you need to keep them running for as long as you need. A unit with plenty of Wh but too little W can't start your refrigerator; a unit with plenty of W but too little Wh will run out long before the outage ends. This guide walks through exactly how to calculate both numbers for your specific situation — camping, CPAP, refrigerator backup, RV, or full emergency prep — using real appliance data rather than a generic size chart.

Common SituationRough Wh Range*Why
Small electronics only (phone, tablet, lights)Under 300WhVery low combined draw, short use windows
Weekend camping (lights, phone, laptop, fan)300–800WhModerate combined draw over a few hours per day
CPAP (single night, no heated humidifier)300–600WhContinuous low draw for 6–8 hours
Refrigerator backup (alone)1,000–2,000Wh per dayCompressor cycles on/off; total depends heavily on the specific fridge
RV (moderate appliance use, multi-day)1,500–3,000WhCombines several moderate loads over longer stretches without full-time shore power
Multiple appliances / general emergency backup2,000–4,000Wh+Several simultaneous or sequential loads across a full day
Home emergency backup (fridge + electronics + lights)2,500–3,500Wh+ per dayCombines cycling and continuous loads across a household

*These are starting reference ranges based on typical appliance combinations, not a substitute for calculating your own specific devices — work through the method below for a number that actually fits your situation.

Watts vs. Watt-Hours: What's the Difference?

Watts (W) measure the rate of power draw at a given moment — how much a device pulls while it's running. Watt-hours (Wh) measure total energy over time — watts multiplied by the hours something runs. A kilowatt-hour (kWh) is simply 1,000Wh, a unit you'll see on manufacturer specs for larger batteries. Running watts is what a device draws while operating normally; surge (startup) watts is a brief spike some devices need at the moment they switch on, particularly anything with a motor or compressor.

A simple way to see the difference: a 100W device running for 5 hours uses 500Wh (100 × 5). A 1,000W device running for 5 minutes (1/12 of an hour) uses about 83Wh (1,000 × 1/12). The wattage tells you what you can plug in; the watt-hours tell you how long you can keep it going.

How to Calculate Solar Generator Size

Work through these steps using your own devices, not a generic example:

Step 1: List the appliances/devices. Write down everything you actually need to power.

Step 2: Determine running wattage. Check each device's nameplate or manual — this is usually the most accurate source, more reliable than a generic chart, since actual models vary.

Step 3: Determine startup/surge wattage. Note which devices have a motor or compressor, and look for a published surge or starting-watts figure if available.

Step 4: Estimate how long each device will run. Be specific and realistic rather than assuming worst-case, all-day use for everything.

Step 5: Calculate energy consumption. Multiply each device's watts by its hours to get Wh, then add every device together.

Step 6: Add a reasonable reserve. A 20–30% buffer accounts for inverter losses, temperature effects, and normal variance from your estimate.

Step 7: Check the generator's inverter output. Confirm the continuous output rating comfortably exceeds your combined simultaneous load.

Step 8: Check battery capacity. Confirm the Wh rating comfortably exceeds your buffered total.

Step 9: Check solar input/charging capability. Confirm it matches how quickly you'll realistically need to recharge, and how you plan to do it (solar, AC, or both).

Calculator

Solar Generator Size Calculator

Check the devices you need to power, adjust the watts/hours if needed, then calculate your recommended size.

Use Device Watts Hours/day Surge (W)

Default watt/hour values are typical planning estimates, not measurements of your specific devices. Edit any field to match your actual appliances — check the nameplate or manual for the most accurate number.

Your Estimated Requirements

Daily Energy Needed
0 Wh
With 25% Buffer
0 Wh
Continuous Output Needed
0 W
Recommended Surge Rating
0 W

These figures are planning estimates based on the watts and hours you entered, assuming roughly 85% usable efficiency after inverter and battery losses. Actual results vary by device, temperature, battery age, and real-world conditions. Continuous output assumes every checked device could run at the same time — if that's unrealistic for your situation, you can lower it accordingly. Always confirm a specific generator's continuous and surge ratings against your own devices before buying. This tool provides general estimates, not a guarantee of performance for any product or medical device — for CPAP or other medical equipment, confirm power requirements with the manufacturer.

The Formulas

Energy consumption: Watts × Hours = Watt-hours

Multiple appliances: Add the Wh requirements of every appliance operating during the relevant period

Approximate runtime: Usable battery Wh ÷ Device wattage = Approximate runtime

Real-world runtime will typically come in somewhat below this simplified calculation because of inverter conversion losses, battery-management overhead, temperature effects, and the fact that a device's actual draw rarely matches its nameplate figure exactly. Treat these formulas as planning tools, not guarantees.

Appliance Wattage Reference Table

Device/ApplianceTypical Running Watts*Possible Startup SurgeExample: Hours UsedEstimated Wh
Smartphone charger5–10WNone2 hrs to full charge10–20Wh
Laptop~50WNone4 hrs~200Wh
LED light bulb5–10WNone5 hrs25–50Wh
Wi-Fi router/modem10–20WNone24 hrs240–480Wh
Flat-screen TV~120WNone3 hrs~360Wh
Box/window fan55–250WMinimal6 hrs330–1,500Wh
CPAP (no heated humidifier)30–60WNone8 hrs240–480Wh
Refrigerator (frost-free, ~16 cu ft)~700–725W nameplate; ~150–250W while compressor runs~800–1,200W24 hrs plugged in (compressor runs roughly 1/3 of that time)~1,000–2,000Wh/day
Microwave750–1,500WMinimal beyond running watts10 min/day125–250Wh/day
Coffee maker900–1,200WMinimal10 min150–200Wh
Electric kettle~1,000–1,500WMinimal10 min165–250Wh
Blender~300–1,000WMinimal5 min25–85Wh
Small chest freezer100–400W runningSimilar surge pattern to refrigerators24 hrs plugged in, cycling~250–600Wh/day
Portable space heater750–1,500WMinimal2 hrs1,500–3,000Wh
Window air conditioner~500–1,500W (varies by size)Can exceed running watts at startup4 hrs2,000–6,000Wh
Corded power tool (drill, saw)~600–1,500W depending on toolCan be significantly higher at startupVariesVaries

*Figures reflect commonly published nameplate and typical-use ranges (U.S. Department of Energy consumer guidance and cross-checked appliance data), not a specific product measurement. Always check your own appliance's label or manual for its actual rated wattage — models vary. Hours-used and resulting Wh columns are illustrative examples, not universal defaults.

Solar Generator Size Classes

Solar Generator ClassApprox. Battery CapacityTypical Output Range*Suitable ForLimitations
Under 500WhUnder 500WhOften 300–600W continuousPhones, small electronics, basic campingCan't sustain a refrigerator or high-draw appliances
500–1,000Wh500–1,000WhOften 500–1,500W continuousCPAP, laptop/light combos, short camping tripsLimited runtime for compressor-based appliances
1,000–2,000Wh1,000–2,000WhOften 1,000–2,200W continuousRefrigerator backup, moderate RV use, small emergency kitsMay need frequent recharging for multi-day, multi-appliance use
2,000–3,000Wh2,000–3,000WhOften 2,000–2,400W+ continuousMultiple appliances, stronger home-backup setupsHeavier and less portable; higher upfront cost
3,000Wh+3,000Wh and up, often expandableOften 3,000–4,000W+, some with 120/240V supportWhole-home-leaning backup, extended off-grid useLargely stationary; significant weight and cost

*Output ranges vary meaningfully by specific model — battery capacity and output wattage are separate specifications, and a class boundary here doesn't guarantee any specific unit's output. Confirm both numbers directly on the product you're considering; see our Best Solar Generators comparison for current examples across these ranges.

Choosing by Use Case

Use CaseSuggested Capacity RangeImportant SpecificationMay Support
Phone/laptop backupUnder 500WhPortability over outputMultiple phone charges, several hours of laptop use
Camping300–1,000WhWeight, and solar input if relying on panelsLights, phone/laptop charging, a fan, depending on trip length
CPAP300–600Wh per nightContinuous low-wattage output; confirm your specific machine's draw, including humidifier useOne or more nights depending on capacity and machine settings
Refrigerator backup1,000–2,000Wh/daySurge output matching compressor startupA standard refrigerator for a day between recharges, depending on the specific unit
RV use1,500–3,000WhContinuous output for multiple simultaneous loadsLighting, electronics, and moderate appliance use over a multi-day stay
Weekend off-grid use500–1,500WhSolar input if recharging away from AC powerLighting, device charging, and light appliance use over 2–3 days
Short power outages500–1,500WhContinuous output matched to your essential devicesA few hours to overnight coverage of essentials
Emergency home backup2,000–4,000Wh+Combined continuous output and surge capacity for multiple appliancesRefrigerator, electronics, and lighting together, depending on total load
Multiple appliances simultaneously2,000Wh+Continuous output rating specifically — capacity alone doesn't guarantee thisVaries widely; calculate your specific combined load

Language throughout this table is intentionally cautious ("may support," "depending on") because actual results vary by specific appliance, generator model, and conditions — use the calculation steps above with your own numbers rather than relying on a size class alone.

What Can Different Sizes Actually Run?

Around 500Wh: Enough for several phone charges, a few hours of laptop use, or a handful of LED lights over an evening. Not enough to reliably sustain a refrigerator's daily cycling or run high-draw appliances like a microwave for extended periods, since even short bursts at 750W+ can consume a large share of this size's total capacity quickly.

Around 1,000Wh: Comfortable for a full night of CPAP use, a laptop and lights combined over several hours, or several hours of refrigerator cycling — though likely not a full 24-hour refrigerator cycle without recharging, depending on the specific fridge's actual compressor runtime.

Around 2,000Wh: Often enough for a standard refrigerator across a day (cycling on and off, not running continuously), combined with some electronics and lighting — real-world results still depend heavily on your specific refrigerator's efficiency and how often its door opens.

Around 3,000Wh: Supports a broader combination — refrigerator plus multiple electronics plus occasional higher-draw use like a microwave — with more buffer for a multi-appliance day than smaller classes provide.

5,000Wh and up: Positions you toward multi-day, multi-appliance coverage or a meaningful step toward whole-home-leaning backup, particularly when paired with expansion batteries or strong solar recharging — but at this scale, weight and stationary placement become real practical factors, not just cost.

None of these figures are guarantees for any specific product or appliance combination — they're planning reference points to calculate from, using the method and appliance table above.

Worked Examples

Example 1: Refrigerator

A refrigerator's nameplate might list around 700W, but according to the U.S. Department of Energy, that's the maximum draw while the compressor is actively running — not a continuous draw. DOE's own guidance suggests a rough estimate: divide the total time the refrigerator is plugged in by three to estimate how long it's actually running at that peak wattage, since refrigerators cycle on and off to maintain temperature. Applying that: if a fridge is plugged in for 24 hours, it might actually run its compressor for roughly 8 of those hours. At roughly 700W running wattage for 8 hours, that's approximately 5,600Wh — though independent appliance-wattage research suggests many standard refrigerators draw closer to 150–250W while the compressor runs (with the nameplate figure representing a peak rather than typical value), which would put a more realistic daily estimate closer to 1,000–2,000Wh. This range is wide because refrigerator efficiency varies significantly by model, age, and usage pattern — check your specific refrigerator's actual energy guide label (the yellow ENERGY STAR-style tag) for a more precise annual kWh figure, then divide by 365 for a daily estimate.

Example 2: Camping

Say you want lights (2 LED bulbs at 8W each, 4 hours), a phone (10W, 2 hours to charge), a laptop (50W, 3 hours), and a fan (100W, 5 hours):

  • Lights: 16W × 4h = 64Wh

  • Phone: 10W × 2h = 20Wh

  • Laptop: 50W × 3h = 150Wh

  • Fan: 100W × 5h = 500Wh

  • Total: 734Wh

  • With a 25% buffer: ~918Wh

This points toward a unit in the 800Wh–1,000Wh range for this specific combination — smaller if you drop the fan or shorten its hours, larger if you're camping for multiple days without recharging.

Example 3: Emergency Home Backup

Say you need a refrigerator (~1,500Wh/day, using a mid-range estimate from the refrigerator example above), a Wi-Fi router (15W × 24h = 360Wh), 3 LED lights (24W total × 5h = 120Wh), phone charging (20Wh), and a laptop (50W × 4h = 200Wh):

  • Refrigerator: ~1,500Wh

  • Router: 360Wh

  • Lights: 120Wh

  • Phone: 20Wh

  • Laptop: 200Wh

  • Total: ~2,200Wh

  • With a 25% buffer: ~2,750Wh

This points toward a unit in the 2,500Wh–3,000Wh class. Separately, check continuous output: none of these devices individually draws more than a couple hundred watts, but if the refrigerator's compressor kicks on while the microwave (not included here) is also running, your continuous output requirement climbs — this is why simultaneous loads, not just total Wh, determine your output requirement.

Example 4: CPAP

CPAP power draw depends heavily on the specific machine and settings — a unit without a heated humidifier commonly draws in the 30–60W range, while heated humidifier and heated-tubing features can increase that meaningfully. For an 8-hour night at 40W (a mid-range estimate, not a guarantee for your specific machine): 40W × 8h = 320Wh, plus a buffer bringing it to roughly 400Wh. Always check your specific CPAP model's power rating (from the manufacturer's manual, not a generic estimate) before relying on this figure, since actual consumption varies by machine and by whether humidification is in use. This guide provides general planning information, not medical guidance — consult your CPAP manufacturer or equipment provider with any device-specific power questions.

Surge Power: Why It Matters as Much as Battery Capacity

Many appliances with a motor or compressor — refrigerators, freezers, well pumps, power tools, air conditioners — draw meaningfully more power for a brief moment at startup than they do once running. A refrigerator might run at 150–250W but spike toward 800–1,200W for a second or two when the compressor kicks on. If a solar generator's surge rating can't cover that spike, the appliance may fail to start at all — even if the unit's battery capacity and continuous output otherwise look sufficient on paper. Always check a device's startup or surge wattage (sometimes listed separately from running watts on the nameplate or manual) against your generator's surge rating specifically, not just its continuous rating.

Solar Input and Recharging

Battery capacity tells you how much you can store; solar input tells you how fast you can refill it. A unit with a 1,000Wh battery and a 200W solar input will take considerably longer to fully recharge from panels than a unit with the same capacity and a 600W solar input — assuming both have enough connected panel wattage to actually use that input rate. Real-world solar charging is also affected by weather conditions, panel orientation relative to the sun, ambient temperature, and time of day — a panel's rated wattage assumes near-ideal sunlight, and actual output is often meaningfully lower. A large battery paired with limited solar input can mean waiting a full day or more for a complete solar recharge, which matters most if you're relying on solar as your primary (not backup) charging method.

Charging MethodTypical SpeedBest ForDepends On
AC (wall outlet)Generally fastest; some current units offer sub-1-hour full charges with fast-charging modesQuick top-offs before/after an outageGrid power being available
Solar panelsSeveral hours in good sun, longer in poor conditionsOff-grid or extended use without AC accessPanel wattage, weather, sun angle, and the unit's max solar-input rating
Car (12V)Slowest of the common methodsBackup or light top-up while travelingVehicle runtime and the unit's 12V input limits

Battery Chemistry: A Quick Note

Most current solar generators use LiFePO4 (lithium iron phosphate) batteries, valued for a notably longer cycle life (often thousands of charge cycles to 80% capacity) and better thermal stability compared with older lithium chemistries, at the cost of slightly more weight per Wh. Some lighter, older, or budget-focused models use NMC lithium instead, trading a shorter typical cycle life for reduced weight. Neither chemistry is "sufficient" or "insufficient" on its own — chemistry affects lifespan and weight more than it affects sizing decisions, so treat this as a secondary consideration after you've nailed down your Wh and W requirements. For more detail on how chemistry fits into the bigger buying picture, see our solar generator buying guide.

"Solar Generator" vs. "Portable Power Station"

Quick terminology note: most brands and retailers use these terms interchangeably today. Both describe a battery unit that stores energy and can be recharged by solar panels, among other methods — "solar generator" doesn't mean it runs directly on sunlight the way a gas generator runs on fuel.

Common Sizing Mistakes

MistakeBetter Approach
Looking only at watt-hoursCheck continuous and surge output too — Wh alone doesn't tell you what you can run at once
Ignoring surge wattageIdentify the highest startup spike among your devices, especially motors and compressors
Using nameplate wattage without considering duty cycleFor cycling appliances (fridges, freezers, AC units), estimate actual running time rather than assuming 24/7 peak draw
Forgetting inverter lossesAdd a 20–30% buffer to your calculated Wh total
Forgetting other devices running simultaneouslyAdd up everything you'd realistically run at the same time when checking continuous output
Assuming solar panels always produce their rated outputPlan around realistic sun conditions, not ideal-case panel wattage
Buying far more capacity than neededCalculate your actual load rather than sizing up "just in case"
Buying too little capacityInclude a reasonable buffer and account for multi-day use if relevant
Ignoring recharge timeConsider how quickly you'll realistically need the unit back to full
Ignoring expansion optionsConsider whether your needs might grow before locking into a fixed-capacity unit

How to Choose the Right Size: A Quick Framework

Answer these before buying:

  1. What appliances do I need to power?

  2. How many watts do they require (running)?

  3. Which of them have startup surges, and how large?

  4. How many hours will I need each one?

  5. How much battery capacity (Wh) do I need, with a buffer?

  6. How much inverter output (W) do I need for simultaneous use?

  7. How quickly must the unit recharge given my situation?

  8. Will I recharge primarily from solar panels, AC, or both?

  9. Do I need expandable battery capacity for future needs?

If you want to see how specific current models stack up against these numbers, our Best Solar Generators comparison covers seven models across different capacity classes with verified specifications.

Frequently Asked Questions

What size solar generator do I need for a refrigerator?

Commonly in the 1,000–2,000Wh range for a day's cycling, though this varies significantly by the specific refrigerator's efficiency and compressor duty cycle — check the appliance's energy guide label for a more precise figure, and confirm the generator's surge rating covers the compressor's startup spike.

What size solar generator do I need for a house?

It depends entirely on which appliances you're backing up and for how long — a small electronics setup might need under 500Wh, while backing up a refrigerator plus several other devices for a full day often calls for 2,500Wh or more. Work through the calculation steps above using your own device list.

Is 1,000 watts enough for a solar generator?

"1,000 watts" describes output, not capacity — whether it's enough depends on whether your combined simultaneous load (and highest surge) stays under that number, which you'd need to check against your specific appliances.

Is 2,000 watts enough for home backup?

For many essential-device combinations, yes, but it depends on your specific appliance list — particularly whether you're running high-draw items like a microwave or space heater simultaneously with other loads.

How many watt-hours do I need?

Add up the Wh (watts × hours) for every device you plan to run over the relevant period, then add a 20–30% buffer — see the step-by-step method and worked examples above.

How long will a 1,000Wh solar generator last?

It depends on what you're running — a low-draw device like a CPAP (30–60W) could last roughly 14–28 hours on 1,000Wh (before efficiency losses), while a high-draw appliance would drain the same battery much faster. Divide usable Wh by your device's wattage for a rough estimate.

What size solar generator do I need for camping?

Commonly in the 300–1,000Wh range depending on trip length and how many devices you're running — see the camping worked example above for a full calculation.

What size solar generator do I need for an RV?

Commonly in the 1,500–3,000Wh range for moderate appliance use over multiple days, though larger RVs with air conditioning or heavier loads may need considerably more.

What size solar generator do I need for a CPAP?

Commonly 300–600Wh per night for a machine without a heated humidifier, though your specific model's power draw should be confirmed with its manufacturer.

Can a solar generator run a refrigerator overnight?

Many units in the 1,000Wh-and-up range can, provided the surge rating covers the compressor's startup spike — see the refrigerator worked example above for how to estimate your specific needs.

What is the difference between watts and watt-hours?

Watts measure power draw at a given moment; watt-hours measure total energy used over time (watts × hours). A device's wattage tells you what you can plug in; its watt-hour consumption tells you how long a given battery will sustain it.

How much solar input do I need?

It depends on how much of your recharging will come from solar versus AC power — if solar is your primary method, prioritize a higher solar-input rating and matching panel wattage; if it's a backup to AC charging, a lower input rating is often fine.

Final Summary

Sizing a solar generator correctly means looking at power output, surge capacity, battery capacity, expected runtime, and recharge capability together — not picking a unit based on a single headline watt-hour number. Calculate your actual appliance loads using the steps and tables above, add a reasonable buffer, and check both the continuous and surge output ratings against your highest simultaneous and startup demands. Once you know your numbers, our Best Solar Generators comparison and solar generator buying guide can help you match them to a specific current model.